IEC 62024-1-2008

高频感应元件 电气特性和测量方法 第1部分:毫微亨范围的片式电感器

High frequency inductive components. Electrical characteristics and measuring methods. Part 1:Nanohenry range chip inductor Edition 2.0

适用范围：This part of IEC 62024 specifies electrical characteristics and measuring methods for thenanohenry range chip inductor that is normally used in high frequency (over 100 kHz) range.

实施日期：2008-02-01

DIN EN 60444-1-2000

在aπ网中通过零相技术的石英晶体参数的测量.第1部分:石英晶体的共振频率和抗共振测量的基本方法

Measurement of quartz crystal unit parameters by zero phase technique in a pi-network - Part 1: Basic method for the measurement of resonance frequency and resonance resistance of quartz crystal units ...

适用范围：In the document some formulae of the appendix to IEC 60444-1 are updated, taking into account the modied calibration procedure of the <pi>-network.#,,#

实施日期：2000-09-01

DIN EN 60444-4-1997

在π型网络中采用零相位技术测量石英晶体元件的参数.第4部分:石英晶体元件负荷谐振频率fL负荷谐振电阻RI的测量方法.石英晶体元件其他推导值

Measurement of quartz crystal unit parameters by zero phase technique in a pi-network - Part 4: Method for the measurement of the load resonance frequency <(kursiv)f><(Index)L>, load resonance resistan...

适用范围：The document specifies a method of measuring load resonance frequency f<(Index)L> and load resonance resistance R<(Index)L> in the frequency range up to 30 MHz.

NF C93-370-1-2002

High frequency inductive components - Electrical characteristics and measuring methods - Part 1 : nanohenry range chip inductor.

GB 4783-1984

汽车悬挂系统的固有频率和阻尼比测定方法

实施日期：1985-10-01

BS EN 62024-1-2008

高频率感应元件 电子特性和测量方法 第1部分:纳亨范围芯片感应器

Induktive Hochfrequenz-Bauelemente. Elektrische Eigenschaften und Messmethoden. Chipinduktivit?ten im Nanohenry-Bereich High frequency inductive components. Electrical characteristics and measuring met...

适用范围：This part of IEC 62024 specifies electrical characteristics and measuring methods for thenanohenry range chip inductor that is normally used in high frequency (over 100 kHz) range.

实施日期：2008-08-29

IEC 60444-1 AMD 1-1999

Measurement of Quartz Crystal Unit Parameters by Zero Phase Technique in a Pi-Network. Part 1:Basic Method for the Measurement of Resonance Frequency and Resonance Resistance of Quartz Crystal Units by Zero Phase Technique in a Pi-Network Mesure Des Parametres Des Quartz Piezoelectriques Par La Technique De Phase Nulle Dans Le Circuit En Pi. Partie 1:Methode Fondamentale Pour La Mesure De La Frequence De Resonance Et De La Resistance De Resonance Des Quartz Piezoeletriques Par La Technique De Ph

实施日期：1999-08-01

EN 60444-3-1997

Measurement of Quartz Crystal Unit Parameters by Zero Phase Technique in a Pi-Network Part 3: Basic Method for the Measurement of Two-Terminal Parameters of Quartz Crystal Units up to 200 MHz by Phase Technique in a Pi-Network with Compensation of the Parallel Capacitance Co

DIN EN 60556-2007

Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties(IEC 60556:2006)

实施日期：2007-01-01

IEC 62025-2-2005

高频感应元件 非电气特性和测量方法 第2部分:非电气特性的试验方法

High frequency inductive components - Non-electrical characteristics and measuring methods - Part 2: Test methods for non-electrical characteristics

适用范围：Specifies a test method for the non-electrical characteristics of the surface mounted device inductors to be used for electronic and telecommunication equipment. Defines methods for measuring mechanica...

发布日期：2005-01-28  实施日期：2005-01-28

IEC 60444-11-2010

石英晶体元件参数的测量 第11部分:采用自动网络分析技术和误差校正确定负载谐振频率fL和有效负载电容CLeff的标准方法

Measurement of quartz crystal unit parameters - Part 11: Standard method for the determination of the load resonance frequency fL and the effective load capacitance CLeff using automatic network analyz...

适用范围：IEC 60444-11:2010 defines the standard method of measuring load resonance frequency fL at the nominal value of CL, and the determination of the effective load capacitance CLeff at the nominal frequency...

发布日期：2010-10-07  实施日期：2010-10-07

NF B10-631-2004

Natural stone test methods - Determination of the dynamic modulus of elasticity (by measuring the fundamental resonance frequency).

ASTM C848-1988(2011)

Standard Test Method for Young’s Modulus,Shear Modulus,and Poisson’s Ratio For Ceramic Whitewares by Resonance

实施日期：1988-09-30

BS 1881-209-1990

混凝土试验.第209部分:动态弹性模量测定的推荐方法

Pruefung von Beton. Empfehlungen fuer die Messung des dynamischen Elastizitaetsmoduls Methods of Testing Concrete Part 209:Recommendations for the Measurement of Dynamic Modulus of Elasticity Essais de...

适用范围：Procedure for determining dynamic modulus using longitudinal vibration of laboratory specimens.

实施日期：1990-01-01

EN 62024-2-2009

High frequency inductive components - Electrical characteristics and measuring methods - Part 2: Rated current of inductors for DC to DC converters

DIN EN 60444-8-2004

石英晶体元件参数测试方法 第8部分:表面安装石英晶体元件的紧固件测试

Measurement of quartz crystal unit parameters - Part 8: Test fixture for surface mounted quartz crystal units

适用范围：This part of IEC 60444 explains the test fixture that allows the accurate measurement of resonance frequency, resonance resistance, and equivalent electrical circuit parameters of a leadless surface mo...

实施日期：2004-03-01

IEC 60444-9-2007

石英晶体元件参数的测量 第9部分:压电晶体元件的寄生振荡测量

Measurement of quartz crystal unit parameters - Part 9: Measurement of spurious resonances of piezoelectric crystal units

适用范围：IEC 60444-9:2007 describes two methods for determining the spurious (unwanted) modes of piezoelectric crystal resonators. It extends the capabilities and improves the reproducibility and accuracy compa...

发布日期：2007-02-20  实施日期：2007-02-20

BS 9612 N009-1977

Abgedichtete (kaltverschweisste) Quarzkristalleinheiten fuer Oszillatoren. Detailspezifikation. DN,DQ und DP Gehaeuse,Frequenzbereich 50 bis 125 MHz. Dickenscherungsobertonschwinger (5. Oberton),AT-Schnitt,fuer den eng temperaturbegrenzten Betrieb (temperaturgeregelt). Volles Guetebestaetigungsniveau Detail specification for cold welded seal quartz crystal units for oscillator applications. DN,DQ and DP enclosures,50 to 125 MHz frequency range. Fifth overtone thickness-shear mode,AT-cut,for oper

实施日期：1977-06-15

DIN ISO 3312-1990

烧结金属和硬质合金;弹性模数的测定

Sintered metal materials and hardmetals; determination of young modulus; identical with ISO 3312:1987

适用范围：This standard specifies a method of determination of dynamic (adiabatic) young's modulus by longitudinal oscillations of sintered metal materials and hardmetals.

DIN EN 62024-1-2008

高频感应元件 电气特性和测量方法 第1部分:毫微亨范围的片式电感器

High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor

实施日期：2008-10-01