BS EN 13480-3-2002+A4-2010

Metallic industrial piping. Design and calculation

实施日期：2002-07-04

EN 13746-2004

Surfaces for sports areas Determination of dimensional changes due to the effect of varied water,frost and heat conditions

实施日期：2004-06-30

ISO 13003-2003

纤维增强塑料 循环负荷条件下疲劳性能的测定

Fibre-reinforced plastics -- Determination of fatigue properties under cyclic loading conditions

适用范围：ISO 13003:2003 defines the general procedures for fatigue testing of fibre-reinforced plastic composites under cyclic loading conditions of constant amplitude and constant frequency.

发布日期：2003-12-01  实施日期：2003-12-01

NF C93-400-9-5-2011

Connectors for electronic equipment - Tests and measurements - Part 9-5 : endurance tests - Test 9e : current loading, cyclic.

IEC 60853-3-2002

电缆周期性和事故电流定额的计算 第3部分:带有局部干燥土壤的一切电压电缆的周期性定额因数

Calculation of the cyclic and emergency current rating of cables - Part 3: Cyclic rating factor for cables of all voltages, with partial drying of the soil

适用范围：Gives a method for calculating the cyclic rating factor, for cables of all voltages, where partial drying out of the surrounding soil is anticipated. The method is based on one of the three methods pub...

发布日期：2002-02-18  实施日期：2002-02-18

NF E86-700-3/A3-2009

Metallic industrial piping - Part 3 : design and calculation.

NF E86-700-3/A2-2007

Metallic industrial piping - Part 3 : design and calculation.

DIN EN 13480-3-2002

工业金属管道 第3部分: 设计和计算

Metallic industrial piping - Part 3: Design and calculation

实施日期：2010-10-01

DIN 268-1974

交变冲击负荷切向键与切向键槽

Tangential Keys and Tangential Keyways for Alternating Shock Loads

适用范围：Tangent keys and keyways for alternating shock loadsZusammenhang mit dem von der International Organization for Standardization (ISO) herausgegebenen ISO-Entwurf ISO/DIS 3117 - 1973 siehe Erl?uterungen...

NF A05-116-2008

Corrosion of metals and alloys - Accelerated cyclic tests with exposure to acidified salt spray, "dry" and "wet" conditions.

ISO 7798-1984

越野雪撬 疲劳指标的测定 周期性载荷试验

Cross-country skis -- Determination of fatigue indexes -- Cyclic loading test

适用范围：Specifies a methode for the determination of the fatigue indexes, i.e. the resistance of the skis to changes of bottom camber height or irreversible damage, after a bending test with cyclic loading. Is...

发布日期：1984-07-01  实施日期：1984-07-01

DIN EN ISO 16151-2008

Corrosion of metals and alloys - Accelerated cyclic tests with exposure to acidified salt spray, "dry" and "wet" conditions

实施日期：2008-07-01

DIN EN 12295-1999

塑料管道系统.热水和冷水用热塑性塑料管和相关管件.管接头耐循环压力的检测方法

Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test methods for resistance of joints to pressure cycling; German version EN 12295:1999

适用范围：The document specifies a method for testing the resistance of joints to pressure cycling.

BS EN 13746-2004

运动场表面.由于水、霜冻和热条件变化引起的尺寸变化的测定

Sportboeden. Bestimmung von Massaenderungen aufgrund wechselnder Einwirkung von Wasser,Frost und Waerme Surfaces for sports areas Determination of dimensional changes due to the effect of varied water,...

适用范围：This European Standard specifies a method for the determination of the dimensional stability of synthetic turf, textile surfaces, shock pads and loose-laid synthetic surfaces when subjected to varied w...

实施日期：2004-06-30

IEC 60853-2 AMD 1-2008

修改件1 电缆周期性和事故电流定额的计算 第2部分:18/30(36)kV以上电缆的周期性定额和一切电压电缆的事故定额

AMENDMENT 1 Calculation of the cyclic and emergency current rating of cables. Part 2:Cyclic rating of cables greater than 18/30 (36) kV and emergency ratings for cables of all voltages

适用范围：This amendment has been prepared by IEC technical committee 20: Electric cables.The text of this amendment is based on the following documents: FDIS ...

实施日期：2008-10-01

JB/T 8138.2-1995

电缆附件试验方法 第2部分:恒压负荷循环试验

Test methods for cable accessories--Part 2: Test of load-cycling at constant voltage ...

实施日期：1996-04-14

ISO 21581-2010

木结构 剪力墙用静态和循环横向负载试验法

Timber structures - Static and cyclic lateral load test methods for shear walls

适用范围：ISO 21581:2010 specifies static and cyclic test methods as a basis for the derivation of lateral load resisting parameters which are required in the wind and seismic design of shear walls in timber bui...

发布日期：2010-06-01  实施日期：2010-06-01

BS 2838-1-1988

诊查床.第1部分:固定高诊查床规范

Medizinische Untersuchungs-und Behandlungsbaenke. Baenke mit fester Hoehe Examination and General Treatment Couches Part 1:Specification for Fixed Height Couches Tables d'examen. Tables de hauteur fixe...

适用范围：Requirements for couches, with an adjustable head section, for general use. An optional mounting step is also specified.

实施日期：1988-01-01

EN 13480-3-2012

Metallic industrial piping. Part 3:Design and calculation

实施日期：2012-06-01

NF T54-942-1999

Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling.