IEC 60034-14-2003

旋转电机 第14部分:轴中心高56mm及以上的电机机械振动 振动强度的测量、评价和限值

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity

适用范围：Specifies the factory acceptance vibration test procedures and vibration limits for certain electrical machines under specified conditions, when uncoupled from any load or prime mover. Is applicable to...

发布日期：2003-11-26  实施日期：2003-11-26

BS EN 60034-4-2008

旋转电机.第4部分:试验测定同步电机参数

Rotating electrical machines. Methods for determining synchronous machine quantities from tests

适用范围：This part of IEC 60034 applies to three-phase synchronous machines of 1 kVA rating andlarger with rated frequency of not greater than 500 Hz and not less than 10 Hz.Most of the methods are intended to ...

实施日期：2009-03-31

DIN CLC/TS 60034-18-33-2011

Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses (IEC/TS 60034-18-33:2010); German ve

ISO 7919-3-2009

机械振动 在转轴上测量来评定机器振动 第3部分:耦合的工业机器

Mechanical vibration -- Evaluation of machine vibration by measurements on rotating shafts -- Part 3: Coupled industrial machines

适用范围：ISO 7919-3:2008 gives guidelines for applying evaluation criteria of shaft vibration under normal operating conditions, measured at or close to the bearings of coupled industrial machines.

发布日期：2009-02-01  实施日期：2009-02-01

DIN ISO 7919-3-2009

机械振动 在转轴上测量来评定机器振动 第3部分:耦合的工业机器

Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3: Coupled industrial machines

适用范围： This part of ISO 7919 gives guidelines for applying evaluation criteria of shaft vibration under normal operating conditions, measured at or close to the bearings of coupled industrial machines. Thes...

实施日期：2009-08-01

ISO 14839-3-2006

机械振动 装有活动磁性轴承的旋转机械的振动 第3部分:稳定裕度的评估

Mechanical vibration -- Vibration of rotating machinery equipped with active magnetic bearings -- Part 3: Evaluation of stability margin

适用范围：ISO 14839-3:2006 establishes the stability requirements of rotating machinery equipped with active magnetic bearings (AMB). It specifies a particular index to evaluate the stability margin and delineat...

发布日期：2006-09-01  实施日期：2006-09-01

UL 1004-6-2012

UL Standard for Safety Servo and Stepper Motors Second Edition

实施日期：2012-06-06

DIN EN 60034-3-2009

旋转电机 第3部分:汽轮机或燃气轮机驱动的同步发电机的特殊要求

Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

实施日期：2009-03-01

BS ISO 7919-3-2009

非往复式机械的机械振动.对旋转轴的测量和评定规范.第3部分:耦合工业机械

Mechanische Schwingungen. Bewertung der Schwingungen von Maschinen durch Messungen an rotierenden Wellen. Gekuppelte industrielle Maschinen Mechanical vibration. Evaluation of machine vibration by meas...

适用范围：Vibration, Vibration measurement, Shafts (rotating), Industrial, Steam turbines, Electric generators, Turbocompressors, Turbines, Pumps, Electric machines, Electrical transmission systems, Rotating par...

实施日期：2009-03-31

IEC 60034-14 AMD 1-2007

IEC 60034-14 的修正1

Amendment 1 Rotating electrical machines. Part 14:Mechanical vibration of certain machines with shaft heights 56 mm and higher. Measurement,evaluation and limits of vibration severity Amendement 1 Mach...

适用范围：This is Amendment 1 to IEC 60034-14-2003 (Rotating electrical machines Part 14:Mechanical vibration of certain machines with shaft heights 56 mm and higher -Measurement, evaluation and limits of vibrat...

实施日期：2007-02-01

NF C51-114-2008

Rotating electrical machines - Part 4 : methods for determining synchronous machine quantities from tests.

BS EN 60034-3-2008

Drehende elektrische Maschinen. Besondere Anforderungen an Synchrongeneratoren angetrieben durch Dampfturbinen oder Gasturbinen Rotating electrical machines. Part 3:Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines Machines électriques tournantes. Règles spécifiques pour les alternateurs synchrones entra?nés par turbines. vapeur ou par turbines. gaz. combustion

实施日期：2008-09-30

ISO 14839-4-2012

机械振动 装有活动磁性轴承的旋转机械的振动 第4部分:技术指南

Mechanical vibration -- Vibration of rotating machinery equipped with active magnetic bearings -- Part 4: Technical guidelines

适用范围：ISO 14839-4:2012: a) indicates a typical architecture of an active magnetic bearing (AMB) system so that users can understand which components are likely to comprise such systems and which functions th...

发布日期：2012-03-01  实施日期：2012-03-01

BS EN 60034-15-2009

旋转电机.第15部分:耐用线圈架绕线定子线圈交流旋转电机电平的脉冲电压

Drehende elektrische Maschinen. Steh-Sto?spannungspegel von Formspulen im St?nder drehender Wechselstrommaschinen Rotating electrical machines. Part 15:Impulse voltage withstand levels of form-wound st...

适用范围：This part of IEC 60034 relates to a.c. machines incorporating form-wound stator coils. Itspecifies the test procedures and voltages to be applied to the main and interturn insulation ofsample coils.

实施日期：2009-10-31

IEEE C62.21-2003

Guide for the application of surge voltage protective equipment on ac rotating machinery 1000 v and greater errata 3/22/2006

实施日期：2003-12-10

IEC 60034-28-2012

Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors

发布日期：2012-12-13  实施日期：2012-12-13

EN 60034-15-2009

Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines

DIN EN 60034-26-2007

Rotating electrical machines - Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors

实施日期：2007-08-01

IEC 60034-28-2007

旋转电机 第28部分:三相低压鼠笼式感应电动机用等效电路图量确定的试验方法

Rotating electrical machines. Part 28:Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors

适用范围：This part of IEC 60034 applies to three-phase low-voltage cage induction motors of framenumbers 56 to 400 as specified in IEC 60072-1.This standard establishes procedures to obtain values for elements ...

实施日期：2007-03-01

ISO 8525-2008

机床发出的空气传播噪声 金属切削机床的操作条件

Airborne noise emitted by machine tools -- Operating conditions for metal-cutting machines

适用范围：ISO 8525:2008 describes, with reference to ISO 230-5, the mechanical and acoustical specifications necessary for a reproducible test method for the determination of airborne noise emitted by metal-cutt...

发布日期：2008-06-01  实施日期：2008-06-01