IEC/PAS 62326-20-2011

印制电路板 第20部分:高亮度发光二极管用电子线路板

Printed boards. Part 20:Electronic circuit board for high-brightness LEDs

适用范围：This PAS specifies the properties of the electronic circuit board for high-brightness LEDs(hereafter described as “ECB”).

发布日期：2011-01-26  实施日期：2011-01-26

DIN EN 61754-22-2006

纤维光学连接器接口 第22部分:F-SMA型连接器门类

Fibre optic connector interfaces - Part 22: Type F-SMA connector family

适用范围：This part of IEC 61754 defines the standard interface dimensions for the type F-SMA family of connectors.

实施日期：2006-02-01

GB/T 2423.32-1985

电工电子产品基本环境试验规程 润湿称量法可焊性试验方法

Basic environmental testing procedures for electric and electronic products--Solderability testing by the wetting balance method

实施日期：1986-02-01

BS EN 50324-3-2002

陶瓷材料和元件的压电性能.测量方法.高功率

Piezoelektrische Eigenschaften von keramischen Werkstoffen und Komponenten. Messverfahren. Grosssignal Piezoelectric properties of ceramic materials and components Part 3:Methods of measurement High po...

适用范围：This European Standard relates to piezoelectric transducer ceramics for power applicationover a wide frequency range both as electromechanical or mechanoelectrical converters.This standard covers the l...

实施日期：2002-10-10

DIN EN 60679-1-2008

Quartz crystal controlled oscillators of assessed quality - Part 1: Generic specification

实施日期：2008-02-01

IEC 60749-12 CORR 1-2003

半导体器件 机械和气候试验方法 第12部分:振动、可变频率 勘误表1

SEMICONDUCTOR DEVICES. MECHANICAL AND CLIMATIC TEST METHODS. Part 12:Vibration,variable frequency CORRIGENDUM 1

适用范围：This is Technical Corrigendum 1 to IEC 60749-12-2002 (Semiconductor devices -Mechanical and climatic test methods -Part 12:Vibration, variable frequency)

实施日期：2003-08-01

GB/T 9414.5-1988

设备维修性导则 第6部分:维修性检验

Guide on maintainability of equipment--Part 6:Maintainability verification

适用范围：维修性检验的目的是验证在产品的一定性能范围内其定性和定量的维修性要求是否已经达到。同时包括检验规定的维修活动是否使设备的性能恢复到了规定的水平。检验适用于硬件、软件及维修设施。　　维修性检验是一个评价各种维修...

发布日期：1988-06-22  实施日期：1988-12-01

GB/T 2423.29-1999

电工电子产品环境试验 第2部分: 试验方法 试验U:引出端及整体安装件强度

Environmental testing for electric and electronic products-- Part 2:Test methods Test U:robustness of terminations and integral mounting devices

发布日期：1999-08-02  实施日期：2000-03-01

DIN EN 60068-2-69-2007

Environmental testing - Part 2-69: Tests - Test Te: Solderability testing of electronic components for surface mounting devices (SMD) by the wetting balance method (IEC 60068-2-69:2007)

实施日期：2007-11-01

BS EN 60512-25-3-2001

电子设备连接器 试验和测量 第25-3部分:试验25c 上升时间退化 IEC 60512-25-3:2001

Steckverbinder fuer elektronische Einrichtungen. Mess-und Pruefverfahren. Pruefung 25c. Veraenderung der Anstiegszeit Connectors for Electronic Equipment-Tests and Measurement-Part 25-3:Test 25c-Rise T...

适用范围：This part of IEC 60512 applies to electrical connectors, sockets, cable assemblies or inter-connection systems. This standard describes a method for measuring the effect a specimen has on the rise time...

实施日期：2001-11-16

NF C93-406-3-2009

Connectors for electronic equipment - Product requirements - Part 3 : rectangular connectors - Sectional specification.

EN 60512-16-16-2008

Connectors for electronic equipment - Tests and measurements - Part 16-16: Mechanical tests on contacts and terminations - Test 16p: Torsional strength, fixed male tabs

EN 60444-7-2004

Measurement of quartz crystal unit parameters Part 7: Measurement of activity and frequency dips of quartz crystal units IEC 60444-7:2004

GB/T 2424.11-1982

电工电子产品基本环境试验规程 接触点和连接件的二氧化硫试验导则

Basic environmental testing procedures for electric and electronic products--Guidance for sulphur dioxide test for contacts and connections

NF C93-112-20-1-2000

Fixed capacitors for use in electronic equipment - Part 20 : blank detail specification : fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ.

SJ 20909-2004

户外电子设备紧固件的防护工艺规范

Defending technical specification for electronic equipment fastener of outdoors

适用范围：本规范规定了户外电子设备低合金结构钢、不锈钢或高耐腐蚀铜合金螺纹紧固件防护的要求、工艺和试验方法。 本规范适用于低合金结构钢、不锈钢及高耐腐蚀铜合金螺纹紧固件的防护。

发布日期：2004-10-25  实施日期：2004-12-30

GB/T 12060.3-2011

声系统设备 第3部分：声频放大器测量方法

Sound system equipment - Part 3: Methods of measurement on audio amplifiers

适用范围：本部分规定了放大器规范中应给出的特性，以及其相应的侧量方法。本部分适用于组成专业或家用声系统的模拟放大器以及模拟／数字放大器中的模拟部分。一般地说，所给出的测量方法是与定义有最直接关系的，但并不排除采用能得到...

发布日期：2011-10-31  实施日期：2012-02-01

NF C93-050-1987

一般电气试验

Electronic components. Basic electrical testing procedures.

实施日期：1987-07-31

DIN EN 61076-4-108-2002

电子设备用连接器 第4-108部分:有质量评定的印制电路板接插件 模数节距25mm、具有IEC 60917-1规定2.5 mm基本网格、可用于15 mm侧向填充密度的集成屏蔽功能的电缆与板连接件的详细规范

Connectors for electronic equipment - Part 4-108: Printed board connectors with assessed quality; Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shield...

实施日期：2002-12-01

BS EN 61754-28-2012

Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces. Type LF3 connector family

发布日期：2012-08-31  实施日期：2012-08-31