QJ 500-1989

碳素钢、合金结构钢锻件技术条件

ASTM A178/A178M-2002(2012)

电阻焊碳素钢和碳素锰钢锅炉管及过热器管的规格

Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes

实施日期：2002-09-10

QJ 500A-1998

碳素钢、合金结构钢锻件技术条件

ASTM A563M-2007

碳素钢和合金钢螺母规格(米制)

Standard Specification for Carbon and Alloy Steel Nuts [Metric]

实施日期：2007-12-01

BS EN 14638-3-2010

Ortsbewegliche Gasflaschen. Wiederbefüllbare geschwei?te Gef??e mit einem Fassungsraum von nicht mehr als 150 Liter. Flaschen aus geschwei?tem Kohlenstoffstahl,ausgelegt nach experimentellen Verfahren Transportable gas cylinders. Refillable welded receptacles of a capacity not exceeding 150 litres Part 3:Welded carbon steel cylinders made to a design justified by experimental methods Bouteilles. gaz transportables. Récipients soudés rechargeables d'une capacit inférieure ou égale. 150 litres. Bo

实施日期：2010-12-31

DIN ISO 5755-2004

烧结金属材料 规范

Sintered metal materials - Specifications

适用范围：The document specifies the requirements for the chemical composition and the mechanical and physical properties of sintered metal materials used for bearings and structural parts.

DIN EN 583-6-2009

Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities

实施日期：2009-03-01

ISO 2020-2-1997

航空航天--飞行控制操纵系统用预成形柔性钢丝绳.第2部分:技术规范

Aerospace -- Preformed flexible steel wire rope for aircraft controls -- Part 2: Technical specification

发布日期：1997-07-01  实施日期：1997-07-01

NF A49-903-2003

可运输气瓶.容量为1升及以下的可再充装的、可运输无缝正火碳锰钢气瓶的设计和制造规范

Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless normalised carbon manganese steel gas cylinders up to and including 1 litre.

ASTM A563-2007a

碳素钢和合金钢螺母规格

Standard Specification for Carbons and Alloy Steel Nuts

GB/T 4336-2002

碳素钢和中低合金钢 火花源原子发射光谱分析方法（常规法）

Standard testmethod for spark discharge atomic emission--Spectrometric analysis of carbon and low-alloy steel(routine method)

适用范围：本标准规定了用火花源原子发射光谱测定碳素钢和中低合金钢中碳、硅、锰、磷、硫、铬、镍、钨、钼、钒、铝、钛、铜、铌、钴、硼、锆、砷、锡含量的方法。　　本方法适用于电炉、感应炉、电渣炉、转炉等铸态或锻轧样品的分析。　　本方法可同时测定...

发布日期：2002-09-11  实施日期：2003-02-01

ASTM A568/A568M-2013ae1

高强度低合金热轧和冷轧碳素结构钢薄板一般要求规格

Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for

实施日期：2013-10-01

DIN EN 15048-1-2007

Non-preloaded structural bolting assemblies - Part 1: General requirements

实施日期：2007-07-01

ISO 898-1-2009

碳钢和合金钢制紧固件的机械性能 第1部分:带指定特性的螺栓、螺钉和螺柱 粗牙螺纹和细牙螺纹

Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread

适用范围：ISO 898-1:2009 specifies mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners — th...

发布日期：2009-04-01  实施日期：2009-04-01

NF E25-100-5-2012

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5 : set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread.

NF E25-802-2-2007

Non-preloaded structural bolting assemblies - Part 2 : suitability test.

ISO 2566-1-1984

钢 伸长值的换算 第１部分:碳素钢和低合金钢

Steel -- Conversion of elongation values -- Part 1: Carbon and low alloy steels

适用范围：Specifies a method of converting room temperature percentage elongations after fracture obtained on various proportional and non-proportional gauge lengths to other gauge lengths. The conversions are n...

发布日期：1984-07-01  实施日期：1984-07-01

ASME B16.49-2012

传输和分配系统用工厂预制锻钢对焊感应管弯头

Factory-Made,Wrought Steel,Buttwelding Induction Bends for Transportation and Distribution Systems

实施日期：2012-01-01

GB 4354-1984

优质碳素钢盘条

Quality carbon steel wire rods

ISO 4999-2011

商品级和冲压和结构级连续热镀锡(合金)冷扎碳钢板

Continuous hot-dip terne (lead alloy) coated cold-reduced carbon steel sheet of commercial, drawing and structural qualities

适用范围：ISO 4999:2011 is applicable to cold-reduced carbon steel sheet of commercial, drawing and structural qualities coated by a continuous hot?dip terne (lead alloy) coating process. It includes the group o...

发布日期：2011-01-01  实施日期：2011-01-01