ASTM D4018-1999(2008)

连续碳和石墨纤维束性能试验方法

Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows

适用范围：<p>The properties determined by these test methods are of value in material specifications, qualifications, data base generation, certification, research, and development.</p> <p>These test methods ar...

实施日期：1999-10-10

ISO 20957-1-2013

Stationary training equipment -- Part 1: General safety requirements and test methods

发布日期：2013-09-01  实施日期：2013-09-01

NF C72-105/A3-2012

Tungsten halogen lamps (non-vehicle) - Performance specifications.

ASTM D7012-2013

不同应力和温度状态下完整岩芯试样耐压强度及弹性模数的试验方法

Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures

ASTM C1201/C1201M-2009

用相同静压差测定室外规格石覆层系统建筑性能的试验方法

Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference

适用范围：<p>This test method gives a standard procedure for determining structural performance under uniform static air pressure difference. This typically is intended to represent the effects of wind loads on ...

实施日期：2009-04-01

IEC 61587-1-2011

电子设备用机械结构 IEC 60917和IEC 60297的试验 第1部分:机箱、机柜、分机柜和机架的气候试验、机械试验和安全性能

Mechanical structures for electronic equipment. Tests for IEC 60917 and IEC 60297 series. Part 1:Environmental requirements,test set-up and safety aspects for cabinets,racks,subracks and chassis under ...

适用范围：IEC 61587-1:2011 specifies environmental requirements,test set-up, as well as safety aspects for empty enclosures,i.e. cabinets,racks,subracks and chassis under indoor conditions. The purpose of this s...

实施日期：2011-11-08

EN 12520-2015

Furniture - Strength, durability and safety - Requirements for domestic seating

发布日期：2015-12-23  实施日期：2015-12-23

NF S52-318-2001

滑翔降落伞设备.紧急降落伞.安全要求和试验方法

Paragliding equipment - Emergency parachutes - Safety requirements and test methods.

EN 747-2-2012

Furniture. Bunk beds and high beds. Part 2:Test methods

实施日期：2012-04-01

ASTM D4971-2008

使用径向负荷76mm(3英寸)钻孔千斤顶测定岩石变形现场模量的试验方法

Standard Test Method for Determining In Situ Modulus of Deformation of Rock Using Diametrically Loaded 76-mm (3-in.) Borehole Jack

适用范围：<p>Results of this test method are used to predict displacements in rock mass caused by loads from a structure or from underground construction. It is one of several tests that should be performed.</p...

实施日期：2008-07-01

BS EN 13001-2-2011

Kransicherheit. Konstruktion allgemein. Lasteinwirkungen Crane safety. General design Part 2:Load actions Sécurit?des appareils de levage. charge suspendue. Conception générale. Effets de charge

实施日期：2011-05-31

NF D61-001-2001

家具.座椅.试验方法.强度和耐久性的测定

Domestic furniture - Seating - Test methods - Determination of strength and durability.

ASTM E2322-2003(2009)

实施地面和屋顶用板的横向及集中载荷测试的试验方法

Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction

实施日期：2003-10-01

ISO 13194-2011

箱型垫板 主要要求和试验方法

Box pallets -- Principal requirements and test methods

适用范围：ISO 13194:2011 specifies the definitions, principal requirements and test methods for box pallets of all materials. It applies to box pallets, including post pallets and cage pallets, but is not intend...

发布日期：2011-09-01  实施日期：2011-09-01

ASTM D3967-2008

完整岩芯试样劈拉强度试验方法

Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens

适用范围：<p>By definition the tensile strength is obtained by the direct uniaxial tensile test. But the tensile test is difficult and expensive for routine application. The splitting tensile test appears to off...

实施日期：2008-07-01

NF D62-015-2-2012

Furniture - Bunk beds and high beds - Part 2 : test methods.

IEC/TS 60034-2-3-2013

旋转电机.第2-3部分:换流器供电交流感应电动机的损失和效率测定

Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors

发布日期：2013-11-01 

NF S71-611-9/A1-2011

Personal flotation devices - Part 9 : test methods - Amendment 1.

EN ISO 8611-1-2012

托盘的材料处理 平托盘 第1部分:试验方法

Pallets for materials handling. Flat pallets. Part 1:Test methods

实施日期：2012-08-01

ASTM D7012-2010

不同应力和温度状态下完整岩芯试样耐压强度及弹性模数的试验方法

Standard Test Method for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures

实施日期：2010-01-15