Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
适用范围：<p>The procedures described in Sections 7-9 are primarily intended for (but not limited to) field joining of polyethylene (PE) pipe and fittings, using suitable equipment and appropriate environmental ...
Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
实施日期：2011-08-01
实施日期：1996-03-10
Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
适用范围：<p>This test method is useful to measure the slow crack growth resistance of molded plaques of polyethylene materials at accelerated conditions such as 80<span class=''unicode''>x00B0;</span>C, 2.4-MPa...
实施日期：2011-05-01
Standard Test Method for Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes
适用范围：<p> Brown and Lu <sup>,</sup> show the Charpy impact energy is related to the ultimate critical temperature of the rapid crack propagation [RCP] behavior as measured by the ISO 13477, S-4 test. </p> ...
实施日期：2002-12-10
Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
适用范围：<p id="s00002">1.1 This specification covers a coextruded polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and outer polye...
实施日期：2010-02-15
Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
适用范围：<p>The tests described in this practice are intended to present a method of satisfying the requirements of DOT CFR Title 49, Parts 192.283 and 192.285. </p> <p>The sustained pressure test is intended t...
实施日期：2004-09-01
Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
适用范围：<p>The ATL value is used to set the break-away strength of a weak-link device, or to set other equipment used to limit pulling force during pull-in installation of polyethylene gas pipe, or to determin...
实施日期：2008-05-01
Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene(PEX-AL-PEX)Pressure Pipe
适用范围：<p id="s00002">1.1 This specification covers a coextruded crosslinked polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and ou...
实施日期：2011-09-15
Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
适用范围：This guide describes the design, selection considerations, and installation procedures for the placement of polyethylene pipe or conduit below ground using maxi-horizontal directional drilling equipmen...
实施日期：2011-05-01
Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
适用范围：<p id="s00002">1.1 This guide describes the design, selection considerations, and installation procedures for the placement of polyethylene pipe or conduit below ground using maxi-horizontal directiona...
Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
适用范围：<p>This test method was designed to be used to validate the long-term resistance to pullout of joints designed for use in plastic natural gas piping systems. </p> <p>This test method is used in additio...
实施日期：1996-03-10
Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
实施日期：2011-11-01
Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile- Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
适用范围：<p id="s00002">1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters cover...
实施日期：2008-12-01
Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
实施日期：2011-04-01
Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
适用范围：<p>This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregn...
实施日期：2009-03-01
实施日期：2011-11-01
Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Hydrostatic Pressure
适用范围：<p>If required by the authority having jurisdiction, hydrostatic pressure leak testing may be conducted to discover and correct leaks or faults in a newly constructed or modified polyethylene pressure ...
实施日期：2010-12-01
Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in. to 65 in.
适用范围：<p id="s00002">1.1 This specification covers the polyethylene material and dimensions applicable to flange adapters (FAs) used to connect polyethylene pipes to other flanged pipe and components such a...
实施日期：2011-07-22
Standard Practice for Qualification of a Combination of Squeeze Tool,Pipe,and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe
适用范围：<p>Squeeze-off is widely used to temporarily control the flow of gas in PE pipe. Squeeze tools vary depending on the size of the pipe and the design of the tool. Squeeze-off procedures vary depending o...
实施日期：2003-08-10
请选择需要导出的字段：
请选择需要导出的字段：
知识产权声明 | 服务承诺 | 联系我们 | 客户服务 | 关于我们
网络出版服务许可证：(署)网出证(京)字第072号 互联网药品信息服务资格证书号：(京)-经营性-2016-0015 信息网络传播视听节目许可证 许可证号：0108284
万方数据标准管理系统V2.0 证书号:软著登字第11198474号
京ICP证：010071 京公网安备11010802020237号 京ICP备08100800号-1
客服电话：4000115888 客服邮箱：service@wanfangdata.com.cn 违法和不良信息举报电话：4000115888 举报邮箱：problem@wanfangdata.com.cn 举报专区：https://www.12377.cn
万方数据知识服务平台--国家科技支撑计划资助项目（编号：2006BAH03B01）©北京万方数据股份有限公司 万方数据电子出版社
